Matters needing attention in automatic door maintenance

1、感应自动门报警功能的性能取决于报警探头的性能用户应根据报警的实际需要选配报警探头。DKM-2B控制器成套出厂时配一只热释型报警探头。如果不用报警功能探头不椄即可。

1. The performance of the alarm function of the induction automatic door depends on the performance of the alarm probe, and the user should select the alarm probe according to the actual needs of the alarm. The DKM-2B controller is equipped with a pyroelectric alarm probe when it is factory. If no alarm probe can not Jie.

2、自动门报警探头输出信号接口的类型应为继电器输出接口供电电压应为直流12-15V否则不能由本控制器直接供电。探头耗电应100毫安。根据现场情况可配用多只探头(一般以1――2只为宜)多探头时采用并接方式。探头。应避免其他热源或直射光影响上方应加防雨罩。

2, the automatic gate alarm probe output signal interface type should be the output interface of the relay, the power supply voltage should be DC 12-15V, otherwise it can not be directly powered by the controller. Probe power consumption should be 100 ma. According to the field situation, more than one probe can be used (usually 1 - 2 is appropriate). Probe. Should avoid other heat source or direct light influence, should add rainproof cover above.

3、感应自动门自动停机功能可根据用户的门体行程设置出厂时设定为145秒左右。

3. The automatic stop function of induction automatic door can be set according to the door travel of the user, and it is set to be about 145 seconds when the factory is set.

4、发现自动门开门和关门方向相反时将控制器的端子接线对调即可。同样STOP显示屏指示方向与实际相反时按同法调整接线。

4, find the automatic door opening and closing direction opposite, the controller terminal connection can be switched. Similarly, when the direction of the STOP display direction is opposite to the actual situation, the wiring is adjusted according to the same method.

5、本控制器发生故障时应由专业人员进行维修或与供货方和生产厂联系维修。以免故障扩大影响使用。

By professional technicians to repair or contact with supplier and manufacturer maintenance 5, the controller failure. In order to avoid the failure to expand the use of impact.

6、自动门控制器应保持清洁防止进水或其他有害物质侵蚀。机壳清洁严禁使用有机溶剂。

6, automatic door controller should be kept clean, prevent water ingress or other harmful substances erosion. No organic solvent is used for cleaning the cabinet.

7、自动门的电缆芯数一般不应少于8线(过去有7线的接线不很合理)门体电缆中间不应含有接头。

7, the automatic door of the cable core number should not be less than 8 lines (the past 7 lines of wiring is not reasonable) the door body cable should not contain connectors.

8、遥控发射器应保持外壳好防止挤压振动跌落进水等现象。注意检查电池电压必要时及时更换。当遥控距离过近时一般应更换电池。电池型号为KC12V-23A。遥控器应尽量避开电磁干扰源。

8, remote control transmitter should keep the shell to prevent extrusion, vibration, drop, water and other phenomena. Pay attention to the battery voltage and replace it when necessary. When the remote control distance is too close, the battery should be replaced. The battery type is KC12V-23A. Remote control should avoid electromagnetic interference source as far as possible.

9、遥控器出厂时按编码加密使用不能互换。用户需要更改时可由厂家按要求变更密码。

9. The remote controller is encrypted and can not be interchanged when leaving the factory. When users need to change, the password can be changed by the manufacturer as required.